✎ omron.v7 [ПромАвтоматика]

Эта страница только для чтения. Вы можете посмотреть исходный текст, но не можете его изменить. Сообщите администратору, если считаете, что это неправильно.
====== omron.v7 ======
Частотный преобразователь Omron V7. 

Используемый протокол - MODBUS. 

http://www.omronkft.hu/nostree/pdfs/inverter/cimr-v7az/v7az.pdf


<code yaml>
plugin.peripherial:

  module.icp1:
    portnum:  2
    netaddr:  1
    enable:   on
    type:     omron.v7
</code>



===== Теги =====


<code>
Reg0001
Reg0002
Reg0020
Reg0021
Reg0022
Reg0023
Reg0024
Reg0027
Reg0028
Reg0029
Reg002A

SYSTEM.ErrorCount
SYSTEM.ErrorFlag 
SYSTEM.NetAddr   
SYSTEM.Port
SYSTEM.TimePeriod
SYSTEM.UpdateDate
SYSTEM.UpdateTime

</code>


==== Регистры ====

  * **Reg0001**
    * 0      Run Command - 1: Run, 0: Stop
    * 1      Reverse Run Command   1: Reverse run  0: Forward run
    * 2      External fault                    1: Fault (EFO)
    * 3      Fault Reset Command     1: Reset Command
    * 4      Multi-function input reference 1 (Function selected by n050)
    * 5      Multi-function input reference 2 (Function selected by n051)
    * 6      Multi-function input reference 3 (Function selected by n052)
    * 7      Multi-function input reference 4 (Function selected by n053)
    * 8      Multi-function input reference 5 (Function selected by n054)
    * 9      Multi-function input reference 6 (Function selected by n055)
    * A      Multi-function input reference 7 (Function selected by n056)
    * B-F    (Not used)
  * **Reg0002** - Frequency reference (unit: n152)
  * **Reg0020** - Status signal
    * 0      Run Command  1: Run  0: Stop
    * 1      Reverse Run Command  1: Reverse run   0: Forward run
    * 2      Inverter operation ready   1: Ready  0: Not ready
    * 3      Fault  1: Fault
    * 4      Data setting error  1: Error
    * 5      Multi-function output 1      (1: MA ON  0: MA OFF)
    * 6      Multi-function output 2      (1: P1 ON  0: P1 OFF)
    * 7      Multi-function output 3      (1: P2 ON  0: P2 OFF)
    * 8-F    (Not used)
  * **Reg0021** - Fault description
    * 0      Overcurrent (OC)
    * 1      Overvoltage (OV)
    * 2      Inverter overload (OL2)
    * 3      Inverter overheat (OH)
    * 4 (Not used)
    * 5 (Not used)
    * 6      PID feedback loss (FbL)
    * 7      External fault (EF, EFO), Emergency stop (STP)
    * 8      Hardware fault (FXX)
    * 9      Motor overload (OL1)
    * A     Overtorque detection (OL3)
    * B     Undertorque detection (UL3)
    * C     Power loss (UV1)
    * D     Control power fault (UV2)
    * E     MEMOBUS communications timeover (CE)
    * F     Operator connection fault (OPR
  * **Reg0022** - Data link status
    * 0      Data write in
    * 1 (Not used)
    * 2 (Not used)
    * 3      Upper/lower limit fault
    * 4      Consistency fault
    * 5-F    (Not used)
  * **Reg0023** - Frequency reference (unit: n152)
  * **Reg0024** - Output frequency (unit: n152)
  * **Reg0027** - Output current (10/1 A)
  * **Reg0028** - Output voltage reference (1/1 V)
  * **Reg0029** - Fault description
    * 0 (Not used)
    * 1 (Not used)
    * 2      Input open phase (PF)
    * 3      Output open phase (LF)
    * 4-F    (Not used)
  * **Reg002A** - Alarm description
    * 0      Operation function stop (STP)
    * 1      Sequence error (SER)
    * 2      Simultaneous FWD/REV Run Commands (EF)
    * 3      External Baseblock (BB)
    * 4      Overtorque detection (OL3)
    * 5      Cooling fan overheat (OH)
    * 6      Main circuit overvoltage (OV)
    * 7      Main circuit undervoltage (UV)
    * 8      Cooling fan fault (FAN)
    * 9      Communications fault (CE)
    * A     Option card communications error (BUS)
    * B     Undertorque (UL3)
    * C     Inverter overheat alert (OH3)
    * D     PID feedback loss (FBL)
    * E     Emergency stop (STP)
    * F     Communications waiting (CAL)